Product photo — inflatable pool, garden setting
Inflatable pools
Above-ground pools for garden and family use, in PVC and TPU.
PVC & TPU inflatables · Pools · Since 2008
Inflatables and pools, made end to end.
We develop, sample and manufacture inflatable pools, water toys and fast-setup rigid-wall pools. Eight wholly owned factories, 70+ production lines and 2,000+ people — with our own PVC film made in-house.
Hero image — finished pool in use, outdoor daylight
What we do
We make our own film, our own samples and our own finished product. One supply chain, from resin to shipment.
08
Manufacturing sites
70+
Production lines
2,000+
People
300–400
Catalogue styles
Product lines
Six families, made on the same floor.
Around 90% of our inflatable output is sealed-air construction, and we also build blower-driven pieces such as small inflatable costumes. Steel frames, pumps and other hardware are bought in from matched suppliers and shipped with the product. We do not manufacture advertising inflatables, bouncy castles or large event structures.
Product photo — rigid-wall pool, set up outdoors
Non-inflatable pools
Fast-setup rigid-wall pools: laminated PVC over high-density board or steel frame.
Product photo — frame pool with hardware
Frame pools
Steel-frame pools with laminated PVC walls and matched hardware.
Product photo — water toys on water
Water toys
Swim rings, water rings and towables in sealed-air construction.
Product photo — inflatable furniture
Inflatable furniture
Air beds, sofas and stools for indoor and outdoor use.
Product photo — inflatable boat on water
Outdoor inflatables
Boats and floats for outdoor and on-water leisure.
The catalogue holds 300–400 styles, including our own designs and design patents registered in China, the United States, the EU and Germany.
Manufacturing
Eight factories, and our own film line.
We buy PVC resin rather than finished film: we compound our own formula and calender our own film. Material procurement is 7–10 days shorter, and the formulation stays adjustable for UV resistance, thickness and softness.
Factory exterior — Xuyi, Jiangsu
PVC film calendering line
High-frequency welding in progress
HF welding
High-frequency welding
The main seam process for sealed-air products, with weld tensile tested before each run.
Sewing
Own sewing workshop
Cut-and-sew work stays in-house, so sewing quality and schedule are not outsourced.
Hot-air seam
Hot-air seam welding
Used for TPU constructions where high-frequency welding does not apply.
Gluing
Gluing
For SUP-type construction and bonded assemblies.
Product development
From a sketch to a shipped container.
Six graphic designers, three printers and more than twenty hand-sample makers work inside the factory — so a concept can be turned into a priced, physical sample quickly, and the same specification then goes into volume production.
01 / Idea
Concept sketch on a worktable
Concept
A sketch, a concept, a target price or an existing sample is enough to start.
02 / Design
Designers reviewing artwork
Specification
Our designers propose sizes, film thickness and configuration to reach the target cost.
03 / Sample
Sample making bench
Physical proof
Simple styles sampled in 2–3 days; complex products in 10–15 days. Sample fee by agreement.
04 / Production
Production line in operation
Volume
45–60 days after sample approval; 60–90 days in peak season from August to April.
Quality control
Verification, not reassurance.
Sealed-air products fail by leaking, so we test at every gate and keep the record. If a claim is ever raised, the pre-production and in-production reports from that order are what the discussion starts from.
Verification sequence
- Incoming material Every PVC batch — 6P phthalates free and 18 PAH
- Pre-production test 3–5 pilot units to the physical laboratory
- Pressure hold 100% of units, 24 hours
- Final inspection AQL 1.5, plus third-party inspection on request
In-house physical laboratory — tensile test bench
Specification discipline
| Attribute | Reference | Status |
|---|---|---|
| Material | PVC / TPU | Defined |
| Weld strength | High-frequency weld tensile test | Verified |
| Load and wave tests | Static load, hanging load, wave simulation | Recorded |
| Pressure hold | 100% of units, 24 hours | Verified |
| Final inspection | AQL 1.5 | Controlled |
| Third-party inspection | Above 98% first pass | Measured |
Audits & testing
Audited, tested, documented.
Audit reports are issued per production site. Our audited site is Jiangsu Comco; where a buyer requires production at an audited facility, orders are allocated to it.
Factory audits
Walmart, Target, Disney and Universal factory audits — all current.
Social compliance
amfori BSCI audited, grade C.
Material testing
TÜV testing on PVC every six months.
Design patents
Registered in China, the United States, the EU and Germany.
- Phthalates 10P free
- PAHs 28P
- REACH SVHC
- BPA
- RoHS
- PFAS
- CHCC
- In-house: 6P phthalates
- In-house: 18 PAH
Product-level testing is arranged per order against the destination market; reports are usually issued 7–10 working days after the sample reaches the laboratory. Patent numbers are supplied on request.
Working with us
The commercial facts, up front.
The numbers buyers ask for first, so you can judge fit before you send an enquiry.
| Minimum order | 3,000–5,000 pcs per style, negotiable depending on the product. |
|---|---|
| Sampling | 2–3 days for simple styles; 10–15 days for complex products. |
| Lead time | 45–60 days after sample approval; 60–90 days in peak season (August to April). Periods of 90–120 days occur when sample approval or packaging artwork is delayed on the buyer’s side. |
| Incoterms | FOB Shanghai, FOB Qingdao, EXW. |
| Currency | USD, or cross-border RMB. |
| Markets | Europe, North America, Australia, China and Southeast Asia. |
| Customers | Inflatable and outdoor brands, importers, and the suppliers and buying offices that serve major retail chains. |
Contact
Send a sketch, a sample or a target price.
Tell us the product, the sizes, the colours, the print, the material thickness and the quantity — or just a concept and a target price. We will come back with a recommended specification and a quotation.
ODM development is part of the service: where you have a concept rather than a finished design, our designers will propose the sizes, film thickness and configuration that meet your target cost.
- Company
- Jiangsu Comco Outdoor Products Co., Ltd.
- Head office
- No. 7 Hushan Road, Xuyi County, Huai’an, Jiangsu, China
- Email & telephone
- To be added — details needed before publication.